EN10210 S355K2H Hot Finished SHS and RHS Hollow Sections

S355K2H Hot Finished supplied by Beverly steel Malaysia are of wide range of sizes, odd sizes and exercer a domicile super big sizes from various countries of origin. S355K2H Hot Finished fully comply with EN standard, EN10210 S355K2H hot finished. Available in RHS-Rectangular Hollow Section, SHS-Square Hollow Section and CHS-Circular Hollow Sections, free of internal stresses and with a minimum strength of 355 MPa, allowing the highest fabrication factors and enabling material cost savings and lighter structures, impact tested -20 degree C at 40Joules suitable for low temperature applications.

Application : Deep Water Projects, Power Plants, Offshore Oil and Gas Projects, Structural Design Arts for Buildings and Towers, Structural Support for Building and Facilities Expansion, MRT-Mass Rapid Transit, MTR-Mass Transit Railway, Terminals, Stations, Sea Port Facilities, Air Port Facilities, Transport Vehicles, Theme Parks, Structural for Theme Park Rides and etc...

Nearest Equivalent :UNI 7806 Fe 510 DD1, NF A 35501 E 36-4

S335K2H

– block letter "S" means "STEEL FOR STRUCTURAL APPLICATIONS"

– the next figure means the minimum yield value required for wall thickness ≤ 16 mm

– "K2" means impact test value -20° C min. at 40 joules

– block letter "H" means "HOLLOW SECTION"

The following typical tables concern mechanical and make-it-online chemical properties

Mechanical properties of non-alloy structural steel hollow section
Minimum Yield strength R_eh Mpa						Tensile strength R_m Mpa			Min. elongation A ^{a b} %				Min. impact energy KV ^dJ
Specified thickness mm						Specified thickness mm			Specified thickness mm				At test temperature of
≤ 16	> 16 ≤ 40	> 40 ≤ 63	> 63 ≤ 80	> 80 ≤ 100	> 100 ≤ 120	< 3	> 3 ≤ 100	>100 ≤ 120	< 40	> 40 ≤ 63	> 63 ≤ 100	> 100 ≤ 120	-20°C
≤ 16	> 16 ≤ 40	> 40 ≤ 63	> 63 ≤ 80	> 80 ≤ 100	> 100 ≤ 120	< 3	> 3 ≤ 100	>100 ≤ 120	< 40	> 40 ≤ 63	> 63 ≤ 100	> 100 ≤ 120	40Joules
355	345	335	325	315	295	510-680	470-630	450-600	22	21	20	18	40Joules

Maximum carbon equivalent value (CEV) based on cast analysis^a
Hot Finished Hollow Sections		Maximum CEV in % for specified thicknesses in mm
Steel Grade	Steel number	≤ 16	> 16 ≤ 40	> 40 ≤ 65	> 65 ≤ 120
S355K2H	1.0512	0.45	0.47	0.50	0.53

CHEMICAL ANALYSIS
Steel Grade	Steel number	Type of deoxidation^a	C% max Specified thickness (mm)		Si % max	Mn % max	P % max	S % max	N ^{b c}% max
Steel Grade	Steel number	Type of deoxidation^a	≤ 40	> 40 ≤ 120	Si % max	Mn % max	P % max	S % max	N ^{b c}% max
S355K2H	1.0512	FF	0.22	0.22	0.55	1.60	0.030	0.030	-
a.The deoxidation methods are designated as follows. FN = Rimming steel not permitted FF = Fully killed steel containing nitrogen binding elements in amounts sufficient to bind available nitrogen (e.g. min. 0.020 % total Al, or 0.015 % soluble Al). b. It is permissible to exceed the specified values provided that for each increase of 0.001 % N the P max. content is also reduced by 0.005%. The N content of the cast analysis. however, shall not be more than 0.012 %. c. The maximum value for nitrogen does not apply if the realhealthmethod.com chemical composition shows a minimum total Al content of 0.020 % with a minimum Al/N ratio of 2:1, or if sufficient other N-binding elements are present. The N-binding elements shall be recorded in the Inspection Document.

We supply various origin and wide range of sizes even mega sizes and odd sizes of RHS-Rectangular Hollow Sections,

SHS-Square Hollow Sections and CHS-Circular Hollow Sections fully comply with EN standard - EN10210 S355K2H hot finished. Please send us your valued enquiry or contact us for further information.